New life for dead Tempe network? Another firm has expressed interest in buying the pennies on the dollar assets that remain of the former Kite Networks installation in Tempe from the firm that financed the venture as long as they can negotiate a new, more favorable deal with the city for mounting and removal rights. CTC, Inc., which the East Valley Tribune reports runs networks in the Kansas City, Mo., area, thinks there's an opportunity. The article notes that reception problems were due in part to the prevalence of stucco in Tempe, common in the southwest. Stucco walls layer plaster or other materials on a wire mesh for strength that turns a house into a bit of an accidental Faraday cage, partially shielding the home from electromagnetic radiation. (Could I go so far to say that Tempe's network could be a phoenix? Ouch.)

Wake up, you darn computer: Intel's new Remote Wake motherboards won't work with Wi-Fi, it's important to note. The feature, announced today, will let an incoming VoIP call (the articles all say "phone call over the Internet") to wake a computer, as long as the call comes from a particular source. Of course, the standard SIP protocol for VoIP doesn't have the kind of security and integrity that would allow this; Intel has to overcome the problem with network address translation that renders most computer unreachable from outside the local network without a separate service like GoToMyPC or LogMeIn; and it will only work for computers connected via Ethernet to a local network, because Wi-Fi is off when a computer sleeps, while Ethernet can remain lightly active. I don't have the protocol details yet, but there's long been a Wake on LAN protocol that required support in a router, operating system, and Ethernet card; Intel may be leveraging this.

Braving the Cold (Boot) – A Sneak Peek of My Presentation at Black Hat

by Patrick McGregor

Cold boot attacks aren’t theoretical academic exercises. Cold boot attacks are real. And they’re serious.

In the past few years, companies have poured hundreds of millions of dollars into full disk encryption technologies. Companies expect full disk encryption to reduce the risk of exposure of sensitive information such as intellectual property or customer data. Reality often deviates from what is expected, however. Researchers from Princeton shocked the industry earlier in 2008 when they released a research paper that showed that low-cost “Cold Boot” attacks could be used to defeat the security of most full disk encryption systems. They recently even published all the tools needed to do this at home!

Some have argued that Cold Boot attacks are not serious security threats. I disagree! First, an unskilled person can capitalize on the exploit using simple, automated steps and publicly available tools. In fact, Cold Boot attacks require nothing more than plugging a USB drive into a laptop. Second, the physical target of a Cold Boot attack, such as a laptop, is very easily obtainable (see the recent Ponemon report on laptops lost/stolen in airports – scary!). Third, although many laptops and desktops are stolen via random acts of theft, it is well known that some criminals profit from organized, calculated data theft. It is only a matter of time before we hear of a high-profile data breach that results from a simple Cold Boot attack.

I am excited to present at Black Hat several innovations for preventing Cold Boot attacks. In addition to summarizing how a Cold Boot attack works, I’ll describe four new software techniques for hardening full disk encryption against the attacks. The software technology was developed by myself, Tim Hollebeek, Alexander Volynkin, and Matt White. All of us work for BitArmor, an exciting security startup based in Pittsburgh. Here’s a sneak peek:

· Wash up: Wipe keys immediately before certain OS state transitions, such as before the computer shuts down or goes into hibernation mode – accessing the memory will yield nothing.

· Take advantage of BIOS memory smashing: By strategically placing keys in certain regions of memory, we can rely on the BIOS boot process to overwrite keys before any operating system can dump the contents of memory.

· Is it chilly in here?: Using built-in temperature sensors, we can lock down the system in reaction to temperature drops that may indicate a Cold Boot attack is in progress.

· Create a virtual enclave for keys: We can implement special cryptographic, OS and processor architecture techniques to provide robust protection for keys against the most aggressive cold boot attacks. By creating a “virtual secure enclave” for encryption keys in software, an attacker cannot extract critical keys from memory – even if the RAM is super-cooled.

Hope you can join us at Black Hat as we take an in-depth look at the future of full disk encryption technology.

Stephouse steps into Portland, Ore., void: Local firm Stephouse has built out 5 sq mi of business-grade wireless availability in downtown Portland and 2 sq mi in an underserved part of north Portland using Proxim gear for both Wi-Fi and WiMax service. Wi-Fi use is $20 per month or 1 free hour per day up to 10 free hours per month. The offering seems to focus on the business side, though, in competition with services like Towerstream. Prices aren't listed on the company's site.

Hartford drops Wi-Fi effort: Connecticut's trouble capital city has given up on city-wide Wi-Fi. No surprise. No firms ready to build for free, no money, no tangible goals. My wife grew up in the suburb to the west--West Hartford, prosaically enough--and speculates that the lack of county-oriented government in Connecticut has doomed Hartford to be a civic wasteland. It's recovering a bit as housing affordability goes up, and there's more going on in the city than there used to be. But there won't be Wi-Fi. Incidentally, the Mark Twain House & Museum in Hartford, home of one of the world's first bloggers, is near financial ruin. It's a great piece of American history; I'm hoping it's saved again--it's had many lives since Twain built it and went bankrupt.

If you’re planning to, or are implementing wired 802.1X, wireless security and/or NAC, the contents of this blog may save you hours of time and trouble.

Throughout the implementations I’ve done, for both wired and wireless 802.1X, I’ve developed a procedure for implementing and testing 802.1X each step of the way. Following these steps my seem to be tedious and unnecessarily time-consuming. But, if  you’re just starting with 802.1X, I’m offering a way to implement it in phased pieces that will give you the information to test, confirm and troubleshoot at each step.

To be honest, I frequently skip these steps, but I’ve done many 802.1X implementations and can usually hit the bullseye the first time (unless there’s buggy software or firmware- you guys know who you are). But, if something doesn’t work, I start right back at Number 1 here and I follow this procedure.

1) Configure wired 802.1X
First setup the basic wired 802.1X. Ideally, start with a Windows test, using XP SP3 or a later server edition and PEAP. Provision RADIUS, I recommend Microsoft IAS because it’s well-documented and well supported. Even if you have other future plans, if you’re using Active Directory, start with IAS. You’ll need to setup a test RADIUS group and policy and link to AD. Get a test switch, add it as a RADIUS client, and configure it to talk to your RADIUS. Set up some ports for 1X and enable it on the switch. I recommend testing with PEAP as the authentication method and a Windows credential pass-thru. Note- you’ll need to create a server certificate to use PEAP- a self-signed Microsoft cert is fine.

If this simple configuration doesn’t work, you have some troubleshooting options. First, view the system events log in the RADIUS/AD server and look for informational events from IAS. If the authentication request is making it from the client -> switch -> RADIUS, you’ll see something here. The something you see should tell you if the EAP method is mismatched, or if the credentials were wrong, etc. Your second line of troubleshooting comes if you don’t see any RADIUS log activity. If that happens, throw on a packet capture utility like Wireshark. You want to search for 2 things. First look for conversations from your Test Switch to the RADIUS server (filter on IP or MACs). If you see something here, see where the conversation drops off. If that comes up empty, it means the conversation is terminated between the Test Switch and Test Client. I have some neat tricks for troubleshooting I’ll share with you later.

2) Add in Wireless
If you’re planning to implement 802.1X for wireless, now is the time to throw 802.11 in the mix. It’s harder to sniff wireless traffic for troubleshooting, which is why I recommend starting with wired 1X. Keep it simple, and then start layering. Once you have the wired 1X configured, all you need to do is get your AP ready and configure it just as you did your switch- add it as a RADIUS client and configure it to talk to RADIUS. For wireless, you’ll need to configure encryption also. Note, I recommend (for testing) to begin with your primary VLAN.

If your wireless 802.1X isn’t working, follow our troubleshooting above and re-check settings based on the RADIUS event log contents. If nothing is making it to RADIUS, then most likely something is misconfigured in your AP/Controller and the AP isn’t communicating with the RADIUS server. You know the rest of it’s working (RADIUS, AD, Client) so you can narrow your troubleshooting scope. Once that’s working you can stop if wireless is your goal, or keep going if you’re layering on more security.

3) Replace with Custom Pieces
If you’re planning to use a different RADIUS server or a different supplicant, now would be a good time to start swapping out our vanilla configuration with custom pieces. Replace 1 piece at a time and re-test.

4) Add in NAC or Endpoint Integrity
Most NAC or EI solutions will integrate with your 802.1X infrastructure (if you want them to) and can be ‘consulted’ prior to authenticating and opening the secured port. My suggestion is to always get 1X working 100% before you add any type of integrity or compliance testing.

If you follow these steps, you can turn a complex configuration into a set of simple baby-steps. It may sound stupid, but I promise it’ll work for you every time!

# # #

But Free Press and Public Knowledge found that sometimes when a WOW subscriber visited Yahoo or Google, NebuAd faked an additional packet of data that appears to be the last part of the downloaded Google webpage. The extra packet included NebuAd-written JavaScript that directs users’ browsers to a NebuAd-owned domain named faireagle.com, where the company drops tracking cookies from other domains and companies on the user’s computer. These can be used later to deliver customized ads based off analysis of where people have gone on the web or what search terms they have used.

Cool so not only are they sniffing traffic they are now inject JavaScript and making it appear to originate from Google. This technique is the same one used by the ever popular and super fun Airpwn. Now what would happen if NebuAds servers where compromised? The ultimate JS malware distrubution platform would be born!

Link

Post from: Grumpy Security Guy

When ISPs Attack!

Creative drops Wi-Fi music player: The formerly leading portable music player firm, before Apple and Microsoft entered the biz, confirmed a report that the Zen Share existed, but that the company chose to drop that Wi-Fi-enabled player. An under-wraps player may appear in about two months that could include Wi-Fi--the name Zen X-Fi could be revealing or not, as X-Fi is an audio-processing technology.

Inspiair's physics-defying technology sold, relabeled Max-Fi: I express my doubts about the combination of marketing promises, including area covered, low latency, and speed, and the collision of those promises with the laws of physics as well as regulatory issues. The lack of sales, noted in the article, tends to confirm my opinion, which is precisely what happened with Vivato after early positive response led to devices being built that couldn't meet the mark. Current claims are 30 sq km with 14 access points for outdoor coverage at the port of Antwerp, a network that's in a test. I wrote about Inspiair back in 2006.

Foster City, Calif., turns down MetroFi equipment offer: The city decided against paying $200,000 for MetroFi's gear, which serves about 1,500 people a month, partly because yearly operations would top $125,000.